With the advancement and development of technology in recent years, a new type of product-automatic transfer switching equipment (ATSE) has appeared in the power switching system, which consists of one (or several) transfer switching appliances and other necessary appliances. It is used to monitor the power circuit and automatically convert one or several load circuits from one power supply to another power supply. It is a new type of product dedicated to power conversion. It can be said that automatic transfer switching equipment (ATSE) represents the development direction of power switching system products. The following is a brief introduction to the development history of the power switching system system products. 1 The development history of power switching system products The related products of power switching system are roughly divided into three categories: contactors, air circuit breakers, and automatic power transfer switch appliances (ATSE). The automatic power transfer switches are divided into switching components. There are two types of air switch and load isolating switch. 1.1 Contactor type This type of power switching system uses a contactor as a switching component. The switching function uses an intermediate relay or a logic control module to form a secondary circuit to complete the control function. It is generally a non-standard product. The disadvantage is that the main circuit contactor requires two If the secondary circuit is energized for a long time, it is prone to malfunctions such as temperature rise and heating, contact bonding, and coil burnout. Because it is a non-standard product, it has many components. The quality of the product is restricted by the components and manufacturing process, and the failure rate is high. It has been gradually replaced by new products. 1.2 Air circuit breaker type This type of power switching system uses plastic case air circuit breaker as the switching component, and the switching function is completed by the ATS automatic control unit. It has mechanical and electrical interlocking, complete functions, fewer components, and easy installation. The secondary line, but the price is relatively high, is generally placed in the distribution cabinet and used in places where the calculation current is large (above 630A). The representative products are the ATS products of Schneider Electric and the DPT/SE products of ABB. 1.3 Automatic power transfer switch electrical equipment (ATSE) category This type of power conversion system is an automatic switch that integrates switch and logic control without an external controller, and truly realizes the integration of mechatronics. This kind of power switching system products are uniformly designed and manufactured, small in size and simple in structure. The switch is driven by a motor, and the switching is stable and reliable. The manipulator motor drive only has current through the switch at the moment of switching, and there is no need to provide working current in the steady state. Significant energy saving. The product has no temperature rise, heating, contact bonding, and coil burnout. The switch is equipped with an electromechanical interlocking device, which can realize automatic switching and automatic recovery, automatic switching without automatic recovery, voltage loss, undervoltage, phase failure protection, manual-automatic conversion, delay control, etc., and it is the mainstream product of power switching. Automatic transfer switch electrical equipment (ATSE) related products can be divided into two levels: PC level and CB level. PC level: ATSE that can connect and carry, but not used to break short-circuit current. CB level: ATSE equipped with overcurrent release, its main contact can be connected and used to break short-circuit current. The switching component of PC-level automatic transfer switch equipment (ATSE) is a load isolating switch; the switching component of CB-level automatic transfer switch equipment (ATSE) is an air switch. 2 Scope of application and implementation standards of automatic transfer switch equipment (ATSE) 2.1 Scope of application (1) The altitude does not exceed 2000m; (2) The ambient temperature is not higher than 40°C and not lower than -5°C; Humidity is not more than 95%; (4) no explosive dangerous medium environment, no rain and snow invaded environment; (5) AC 50Hz, rated voltage not exceeding 1000V, DC voltage not exceeding 1500V. 2.2 Executive Standard 2.2.1 International Standard IEC 60947-6-1: 1998 (Version 1.2) "Low-Voltage Switchgear and Control Equipment Part 6: Multifunctional Electrical Appliances Chapter 1 Automatic Transfer Switch Electrical Appliances". IEC 60947-6-1: 1998 (version 1.2) is the IEC 60947-6-1: 1989 version and its first amendment No. 1Amendment (1994-10) and the second amendment No. 2 Amendment (1997-09) Bound edition. 2.2.2 National Standard GB/T 14048.11-2002 "Low-Voltage Switchgear and Control Equipment" Part 6: Multifunctional Electrical Appliances Chapter 1 Automatic Transfer Switch Electrical Appliances. Since GB/T 14048.11-2002 quotes a large number of technical requirements and test methods specified in GB/T14048.1-200 "General Regulations for Low-Voltage Switchgear and Control Equipment", it must be used in combination with GB/T 14048.1-200 . This standard was issued on October 8, 2002 and implemented on April 1, 2003. 3 Key points for the design and selection of automatic transfer switching equipment (ATSE) (1) Determine the rated working voltage and usage category of the automatic transfer switching equipment (ATSE); (2) Select the specifications of the automatic transfer switching equipment (ATSE) according to the calculated current. The product specifications of different manufacturers will be slightly different. The basic principles of selection are as follows: ①PC-level and CB-level ATSE can be used under the existing specifications. In view of the large number of ATSE products on the market, the indicators that need special attention when selecting are: the rated short-circuit making capacity and rated short-time withstand current of PC-level ATSE (if applicable); the rated short-circuit making and breaking of CB-level ATSE Ability; ②In principle, ATSE automatic transfer switch appliances are not used as short-circuit protection appliances, but only as automatic power transfer switches. The front end should be equipped with air circuit breaker protection, which is more appropriate and is conducive to safe use, maintenance and repair in the future; ③ATSE The rated current should be greater than or equal to the overload operating current of its superior air circuit breaker. (3) Determine the switching method and various functions according to the nature and different purposes of each power supply: automatic switching and automatic recovery, automatic switching without automatic recovery, designated priority power supply, non-designated priority power supply, over-voltage detection, frequency detection, fault Phase detection, communication interface, electrical and mechanical interlock, continuously adjustable delay conversion and automatic, remote, and emergency manual control. 4 Conclusion Automatic transfer switching equipment (ATSE) is a new product of power switching system. With the continuous development and progress of technology, it will inevitably develop in the direction of large current, more voltage levels, higher switching reliability, and better functions. , Will be more widely used in industrial and civil buildings.
Correct Use Of Automatic Transfer Switch Appliances
Aug 05, 2021
Leave a message








